收藏本站
AP5724
Applications Information (cont.)
Dimming Control
There are four different types of dimming control circuits:
1. Using a PWM Signal to EN Pin
With the PWM signal applied to the EN pin, the AP5724 is turned on or off by the PWM signal. The LEDs operate at either zero or full current. The
average LED current increases proportionally with the duty cycle of the PWM signal. A 0% duty cycle will turn off the AP5724 and corresponds to
zero LED current. A 100% duty cycle corresponds to full current. The typical frequency range of the PWM signal is below 2 kHz.
2. Using a DC Voltage
For some applications, the preferred method of brightness control is a variable DC voltage to adjust the LED current. The dimming control using a
DC voltage is shown in Figure 3 . As the DC voltage increases, the voltage drop on R2 increases and the voltage drop on R SET decreases. Thus,
the LED current decreases. The selection of R2 and R3 will make the current from the variable DC source much smaller than the LED current and
much larger than the FB pin bias current. For V DC range from 0V to 2V, the selection of resistors in Figure 3 gives dimming control of LED current
from 0mA to 20mA.
AP5724
FB
V DC
R3
100k
R2
5k
R SET
5
Figure 3 Dimming Control Using a DC Voltage
3. Using a Filtered PWM Signal
The filtered PWM signal can be considered as an adjustable DC voltage. It can be used to replace the variable DC voltage source in dimming
control.
4. Using a Logic Signal
For applications that need to adjust the LED current in discrete steps, a logic signal can be used as shown in Figure 4 . R SET sets the minimum LED
current (when the NMOS is off). R SET sets how much the LED current increases when the NMOS is turned on.
AP5724
FB
R INC
Logic
Signal
R SET
Figure 4 Dimming Control Using a Logic Signal
AP5724
Document number: DS31843 Rev. 4 - 2
9 of 15
www.diodes.com
December 2013
? Diodes Incorporated
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
AP5725FDCG-7 IC LED DRIVER WHITE BCKLGT 6-DFN
AP5726WG-7 IC LED DVR WHITE BCKLGT SOT26
AP8800AWT-7 IC LED DRIVER TSOT23-5
AP8800FNG-7 IC LED DRIVER HIGH BRIGHT 10DFN
AP8801M8G-13 IC LED DRIVER HIGH BRIGHT 8MSOP
AP8802HSP-13 IC LED DRIVER HIGH BRIGHT 8SOIC
AP8802SPG-13 IC LED DRIVER HIGH BRIGHT 8SOIC
AP8803WTG-7 IC LED DRIVER CONN CURR TSOT23-5
相关代理商/技术参数
AP5724WUG-7 功能描述:开关变换器、稳压器与控制器 WH LED STEP-UP DC/DC CONV 2-6 LED RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel
AP5725 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:WHITE LED STEP-UP CONVERTER
AP5725_10 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:WHITE LED STEP-UP CONVERTER
AP5725FDCG-7 功能描述:开关变换器、稳压器与控制器 WH LED STEP-UP DC/DC CONV 2-6 LED RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel
AP5725WG-7 功能描述:开关变换器、稳压器与控制器 WH LED STEP-UP DC/DC CONV 2-6 LED RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel
AP5725WUG-7 功能描述:开关变换器、稳压器与控制器 WH LED STEP-UP DC/DC CONV 2-6 LED RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel
AP5726 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:WHITE LED STEP-UP CONVERTER
AP5726_10 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:WHITE LED STEP-UP CONVERTER